Response SA5 E Instructions d'exploitation Page 15
- Page / 52
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
15
8. To select the required sensitivity, set DIP switch 5 of
SW3 as follows:
ON = HIGH sensitivity
OFF = LOW sensitivity
Note: The recommended setting is HIGH. However,
in cases of extreme environmental problems or if
unexplained false alarms are experienced, it may be
necessary to set the sensitivity to LOW. Setting the
device to LOW sensitivity will require a greater amount
of movement in order to trigger the device.
9. Connect the PP3 Alkaline battery to the battery
clip. The LED behind the lens will rapidly ash for
approximately 2-3 minutes until the PIR has stabilised.
The LED will then stop ashing and turn OFF.
10. Check that the detector Circuit Board is located and
set in the correct position to give the detection zone
pattern required.
To adjust the PCB position simply slide it up or down
ensuring that the location legs are aligned with the
required position number marked on the board.
11. To ret the PIR detector to the rear cover, offer the
detector up to the rear cover and locate the clips in the
top edge into the rear cover. Push the lower edge of
the detector into place and ret the xing screw in the
bottom edge of the PIR to secure in position. Do not
over-tighten the xing screws as this may damage the
casing.
Testing the PIR Detector:
12. Ensure that the LED indicator has stopped ashing
rapidly.
13. Use the and buttons to scroll through
the menu until ‘WALK TEST’ is displayed and press
.
‘Walk Test Waiting…’ will be displayed.
14. Walk into and move slowly around the protected
area, each time the detector senses movement the
LED indicator behind the lens will ash.
In addition, the Control Panel will beep to indicate that
the alarm signal has been received and the identity
of the zone that the detector is congured for will be
displayed.
15. If necessary remove the detector from the wall and
adjust the mounting position of the circuit board within
the detector. Repeat step 14 until the detection range
is correct for your needs. (In most cases no adjustment
will be required).
16. Remove the back cover of the PIR detector. The
Control Panel should beep and display “Accessory
Tamper” to show that the detector’s tamper switch has
been activated.
17. Press to return to the top level menu of TEST
MODE.
18. Recongure the PIR Detector for Normal Operation
with DIP switch 4 of SW3 OFF and ret in position on
the wall.
IMPORTANT: In normal operation, the LED indicator
behind the detector lens will not ash on movement
detection, (unless the battery is low).
Note: When the detector is fully installed i.e. battery
cover tted and in operating mode; in order to conserve
power and maximise battery life the PIR Detector will
only detect movement if there has been no movement
detected within the previous 2 minutes.
1 6m
3 9m
5 12m
PCB Position Range
1 2 3 4 5
ON
1 2 3 4 5
ON
- 6 Zone Communicating 1
- Wirefree Alarm System 1
- Tools and Equipment Required: 2
- CONTENTS 3
- KIT CONTENTS 4
- INTRODUCTION AND OVERVIEW 5
- button on their 6
- 7
- 7
- 7
- TYPICAL INSTALLATION 8
- REMOTE CONTROL UNIT 9
- Testing the Remote Control: 10
- INSTALLING THE CONTROL PANEL 11
- Inside View of Control Panel 11
- At the Control Panel: 12
- Using a Remote Control: 12
- PASSIVE INFRA RED (PIR) 13
- MOVEMENT DETECTORS 13
- PIR DETECTOR 14
- Testing the PIR Detector: 15
- 1 2 3 4 5 15
- MAGNETIC CONTACT 16
- DETECTORS 16
- + side is uppermost on each 17
- EXTERNAL SOLAR SIREN 18
- SOLAR SIREN 19
- . 20
- User Access Code 21
- FACTORY SETTINGS 23
- Master User Access Code 24
- LEARN SYSTEM HOUSE CODE 27
- ALARM DURATION 27
- to save and exit, or 28
- RINGS TO ANSWER PHONE 29
- DIALLER DELAY 29
- DIAL METHOD 29
- DIAL MODE 29
- ZONE SETUP 30
- FINAL EXIT SET 31
- ENTRY DELAY 31
- Delay Period 31
- PART-ARM 1 32
- PART-ARM 2 32
- WALK THROUGH 32
- TELEPHONE NUMBERS 33
- ALARM MESSAGE PLAY TIME 34
- RECORD ALARM MESSAGES 34
- REPLAY ALARM MESSAGES 34
- CALL ROUTING 34
- TEL CONFIRM TIMES 34
- EXIT-DELAY PERIOD 35
- ENTRY-DELAY BEEPS 35
- EXIT-DELAY BEEPS 35
- CALL ATTEMPTS 35
- TIME & DATE SETUP 38
- LATCH KEY SETUP 38
- 39
- ANSWERPHONE ON/OFF STATUS 39
- TELEPHONE NUMBER: 40
- REPLAY ANSWERPHONE GREETING 40
- OPERATING INSTRUCTIONS 41
- LEAVING A VOICE MEMO MESSAGE 43
- External Answerphone: 43
- Control Panel 45
- Remote Control 45
- PIR Movement Detector 45
- Magnetic Contact Detector 45
- MAINTENANCE 46
- ALARM RECORD 47
- Symptom / Recommendation 48
- EXTENDING YOUR ALARM SYSTEM 50
- GUARANTEE 50
- 01268 563273 52
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Response SA5 E
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels