Response SA1 E PLUS Instructions d'exploitation

SA1 E, SA1 E PLUS, SA1PF Eand SA2 E Alarm SystemsInstallation and Operating Instructions01 2 34 5 67 8 921

10PIR Detectors are designed to detect movement in a protected area by detecting changes in infra-red radiation levels caused, for e

Note: DO NOT fix the PIR Detectorto metalwork orlocate the unit within 1m of metalwork (i.e. radiators,water pipes, etc) as this could affect t

3. DIP 4 of SW3 is used to configure the PIRDetector for walk test mode, which allows theoperation of the Detector to be checked

The Magnetic contact comprises two parts; aDetector and a Magnet. They are designed to befitted to doors or windows with the Magne

5. If an additional wired Magnetic Contact isrequired, this should be wired to the terminalblock provided in the battery compartment

Siren HousingThe Siren, Strobe Light and Solar Panel are allencapsulated within a tough polycarbonate housing.This housing provides full prote

Setting the Solar SirenEnsure that the Solar Siren main configuration switchif fitted on the LED strobe board is set to “C.U.” for usewith this alarm

Once you have completed setting the Solar Siren, refitthe DIP switch cover and replace the three cover fixingscrews. Do not over tighten the screw as

Testing an Installed SystemThe system should be tested at regular intervals (at leastevery 3 months) to ensure that it is operating correctly.1. Befor

When leaving the premises, the system must beArmed. However, before doing so, check that allwindows are closed and locked, all protect

Kit Contents 3Introduction and Overview 4 System

Disarming the SystemThe system can be disarmed using either theRemote Control or the Remote Keypad as follows:Remote Control:Press the

Remote Keypad:When the battery is low the ‘low-batt’ LED on theRemote Keypad will be illuminated.PIR Movement Detectors:Under low battery condi

22Your alarm system requireds very little maintenance.However, a few simple tasks will ensure its continuedreliability and operation.IMPORTANT: If, fo

23Alarm RecordYou may make a note of your User Access Code and System House Code below. User Access Code

24TroubleshootingSiren immediately sounds when system armed1. Siren tamper switch activated - adjust tamperplunger and ensure that switch fully closes

25PIR Movement Detector not detecting aperson’s movement1. Ensure the battery clip is securely connected.2. Ensure the ‘House Code’ is correctly set t

26Extending your Alarm SystemYour system may be extended to provide additional protection by adding further PIR Movement Detectors, MagneticContact De

Notes:27

Response Electronics Ltd.Roman House, Lysons Avenue, Ash Vale, Surrey GU12 5QFEmail: [email protected]: www.ResponseElectronics.com

3Alarm System SA1 E SA1 E PLUS SA1PF E SA2 EComponents included:External Solar Siren 1

System ArmingThe system has an Instant-Arm and Delay-Arm mode.If the system is armed in Instant-Arm mode then alldetectors will immediately become ful

5The example below shows a typical propertyincorporating the suggested positions for theRemote Keypad, PIR and Magnetic Detectors for

Remote Control UnitThe Remote Control Unit is used to Arm andDisarm the system.The Remote will activate the Instant-Arm, Delay-Armor Disarm fu

Included in SA2 E system, available as an optional accessory for the SA1 E, SA1 E PLUS and SA1PF E systems.The Wireless Remote keypad is used to contr

5.There are two jumper links located above thebattery compartment.J2 jumper link: Reset to Factory defaultJ3 jumper link: System type selection

4.Refit the battery and test it by using the defaultUser Access code of 1 2 3 4.5.If the testing is ok, set the jumper link J2 asshown on Fi